


Installation of New Powerex Laboratory Compressed Air System.
Powerex-Oil-Less Scroll Laboratory Compressed Air System- Specification
BASE MODEL NUMBER: AES-LSO05A5-AES-SPL
SYSTEM CAPACITY: 100 SCFM @ 145 PSIG
HORSEPOWER: 40 HP Total (5HP x 8) RECEIVER SIZE/CONFIGURATION: 200 Gallon – Vertical
ELECTRICAL: 208/230/460V, 3PH, 60Hz (MUST SPECIFY VOLTAGE WHEN ORDERING.)
*System performance shown with all pumps running
General
The Powerex Laboratory Open Scroll Air Compressor System is designed to provide clean, dry air for
applications where the quality of the compressed air is critical. The High-Pressure unit is rated
for a maximum of 145 PSIG. Each system is completely tested before shipment and includes:
▪ Multiple oil-less scroll air compressors and associated equipment.
▪ Corrosion resistant air receiver.
▪ Desiccant air dryers with purge control.
▪ Control panel.
▪ Dew point monitor.
Open Scroll Air Compressor System
The package shall include multiple oil-less scroll air compressors and associated equipment. The
only field connections required will be system intake, exhaust, and power connection at the control
panel. All interconnecting piping, wiring, and vibration isolation pads are included with the
system.
Oil-less Scroll Compressor Pump
Each compressor shall be belt driven oil-less rotary scroll single stage, air-cooled construction
with absolutely no oil needed for operation. Direct drive compressors shall not be used.
▪ The rotary design shall not require any inlet or exhaust valves and shall be rated for 100%
continuous duty.
▪ Tip seals shall be of composite PTFE material and be rated for 5,000 hours operation for 2, 3,
and 5 HP pumps, and rated for 8,000 hours operation for 7.5 and 10 HP pumps.
▪ Compressor bearings shall be external to the air compression chamber and shall be all
serviceable for extended compressor life. Bearing maintenance shall not be required until 5,000
hours. Compressors with bearings that are not accessible for service have a limited life span and
shall not be accepted. Compressors shall have an integral radial flow fan for cooling and shall not
require any additional electric cooling fans.
▪ Each compressor shall have flexible connectors on intake and discharge, an electric drive motor,
a discharge check valve, a fan-cooled aftercooler, a condensate separator* and a high discharge
temperature shutdown switch.
▪ Each compressor module shall have an isolation valve and a moisture separator* with automatic
drain.
Motor
Each compressor shall be belt driven by a 1750 RPM, ODP, NEMA construction motor. Motors running at
speeds higher than 1750
RPM shall not be acceptable. OSHA approved belt guards shall be provided.
4330 Redwood Highway, Suite 100 San Rafael, CA 94903
Tel 415 507-9373 Fax 415 507-9376
Air Receiver
The AMSE National Board registered 200 PSIG working pressure, vertical air receiver is provided
with:
▪ Pressure gauge
▪ Relief valve
▪ Sight gauge
▪ Manual and automatic electric zero loss drain
▪ External paint and internal lining to resist corrosion
Service Slide
The service slide enables easy maintenance access to each pump and motor base mount without having
to remove them from the system.
▪ Unique maintenance friendly base mount slide design.
▪ Allows safe access to important system components necessary for improved pump life.
▪ Allows faster component replacement time.
Motor Slide Base
Maintenance feature designed for easy adjustment of belt tension from the motor slide on the base
mount assembly.
▪ Robust single screw linear belt tension adjustment.
▪ Custom compact design.
PREMIUM NFPA CONTROL PANEL
The control system provides automatic lead/lag activation based on demand and automatic alternation
of all pumps to equalize the amount of usage among the available pumps. The control panel shall
include:
▪ A color touch screen panel which displays the operating status of the unit. The touch screen
will display pump status, pump faults, pump run hours, system pressure, system alarms and service
alert notifications for the pumps, dryers, and dew point monitor.
▪ Building automation communication gateway, with BacNet® protocol. Ethernet port for connection
to BacNet® /IP server or direct connection to facility Ethernet for viewing of system operations
and status via device IP-address.
▪ A PLC controller that includes logic programmed to appropriately manage start-stop, lead-lag,
and other pump operations.
▪ UL508A listed control panel in a NEMA 12 enclosure.
AIR PURIFICATION SYSTEM
▪ Dual heat-less, automatic pressure swing regenerative desiccant air dryers
▪ Designed to produce a dew point of -40F
▪ Dual cyclonic water separators
▪ Dual .01 micron coalescing pre-filter with element change indicator and automatic condensate
drain
▪ Dual 1 micron particulate after-filter with element change indicator
▪ Dual .01 Micron particulate final filter with element change indicator
▪ Dual pressure reducing valves
▪ Automatic dew point dependent switching to reduce purge frequency
▪ Purge muffler for quiet operation
MONITORING EQUIPMENT
• Dew point monitor with audible/visual alarms & dry contacts for remote alarm signal
SYSTEM CONNECTIONS
The system is shipped with a flexible connector for discharge. Isolation pads included.
Installation of New Powerex Laboratory Compressed Air System.
Powerex-Oil-Less Scroll Laboratory Compressed Air System- Specification
BASE MODEL NUMBER: AES-LSO05A5-AES-SPL
SYSTEM CAPACITY: 100 SCFM @ 145 PSIG
HORSEPOWER: 40 HP Total (5HP x 8) RECEIVER SIZE/CONFIGURATION: 200 Gallon – Vertical
ELECTRICAL: 208/230/460V, 3PH, 60Hz (MUST SPECIFY VOLTAGE WHEN ORDERING.)
*System performance shown with all pumps running
General
The Powerex Laboratory Open Scroll Air Compressor System is designed to provide clean, dry air for
applications where the quality of the compressed air is critical. The High-Pressure unit is rated
for a maximum of 145 PSIG. Each system is completely tested before shipment and includes:
▪ Multiple oil-less scroll air compressors and associated equipment.
▪ Corrosion resistant air receiver.
▪ Desiccant air dryers with purge control.
▪ Control panel.
▪ Dew point monitor.
Open Scroll Air Compressor System
The package shall include multiple oil-less scroll air compressors and associated equipment. The
only field connections required will be system intake, exhaust, and power connection at the control
panel. All interconnecting piping, wiring, and vibration isolation pads are included with the
system.
Oil-less Scroll Compressor Pump
Each compressor shall be belt driven oil-less rotary scroll single stage, air-cooled construction
with absolutely no oil needed for operation. Direct drive compressors shall not be used.
▪ The rotary design shall not require any inlet or exhaust valves and shall be rated for 100%
continuous duty.
▪ Tip seals shall be of composite PTFE material and be rated for 5,000 hours operation for 2, 3,
and 5 HP pumps, and rated for 8,000 hours operation for 7.5 and 10 HP pumps.
▪ Compressor bearings shall be external to the air compression chamber and shall be all
serviceable for extended compressor life. Bearing maintenance shall not be required until 5,000
hours. Compressors with bearings that are not accessible for service have a limited life span and
shall not be accepted. Compressors shall have an integral radial flow fan for cooling and shall not
require any additional electric cooling fans.
▪ Each compressor shall have flexible connectors on intake and discharge, an electric drive motor,
a discharge check valve, a fan-cooled aftercooler, a condensate separator* and a high discharge
temperature shutdown switch.
▪ Each compressor module shall have an isolation valve and a moisture separator* with automatic
drain.
Motor
Each compressor shall be belt driven by a 1750 RPM, ODP, NEMA construction motor. Motors running at
speeds higher than 1750
RPM shall not be acceptable. OSHA approved belt guards shall be provided.
4330 Redwood Highway, Suite 100 San Rafael, CA 94903
Tel 415 507-9373 Fax 415 507-9376
Air Receiver
The AMSE National Board registered 200 PSIG working pressure, vertical air receiver is provided
with:
▪ Pressure gauge
▪ Relief valve
▪ Sight gauge
▪ Manual and automatic electric zero loss drain
▪ External paint and internal lining to resist corrosion
Service Slide
The service slide enables easy maintenance access to each pump and motor base mount without having
to remove them from the system.
▪ Unique maintenance friendly base mount slide design.
▪ Allows safe access to important system components necessary for improved pump life.
▪ Allows faster component replacement time.
Motor Slide Base
Maintenance feature designed for easy adjustment of belt tension from the motor slide on the base
mount assembly.
▪ Robust single screw linear belt tension adjustment.
▪ Custom compact design.
PREMIUM NFPA CONTROL PANEL
The control system provides automatic lead/lag activation based on demand and automatic alternation
of all pumps to equalize the amount of usage among the available pumps. The control panel shall
include:
▪ A color touch screen panel which displays the operating status of the unit. The touch screen
will display pump status, pump faults, pump run hours, system pressure, system alarms and service
alert notifications for the pumps, dryers, and dew point monitor.
▪ Building automation communication gateway, with BacNet® protocol. Ethernet port for connection
to BacNet® /IP server or direct connection to facility Ethernet for viewing of system operations
and status via device IP-address.
▪ A PLC controller that includes logic programmed to appropriately manage start-stop, lead-lag,
and other pump operations.
▪ UL508A listed control panel in a NEMA 12 enclosure.
AIR PURIFICATION SYSTEM
▪ Dual heat-less, automatic pressure swing regenerative desiccant air dryers
▪ Designed to produce a dew point of -40F
▪ Dual cyclonic water separators
▪ Dual .01 micron coalescing pre-filter with element change indicator and automatic condensate
drain
▪ Dual 1 micron particulate after-filter with element change indicator
▪ Dual .01 Micron particulate final filter with element change indicator
▪ Dual pressure reducing valves
▪ Automatic dew point dependent switching to reduce purge frequency
▪ Purge muffler for quiet operation
MONITORING EQUIPMENT
• Dew point monitor with audible/visual alarms & dry contacts for remote alarm signal
SYSTEM CONNECTIONS
The system is shipped with a flexible connector for discharge. Isolation pads included.